Tacoma Front Winch Bumper | Blitz | 3rd Gen (16-23)
★★★★★
4.87/5 Stars. (23 Reviews)
- CNC cut and formed from .188" steel or .250" aluminum.
- Tubework option includes 1.75" x .120" tubework for added grill protection.
- Compatible with most 8-10k non-integrated solenoid or removable selenoid winches.
- Built in provisions for a 20" single row light bar (22" max mounting width)
- Not compatible with Onx6 20" Light Bar.
- Proudly designed and made in the USA.
- Will work with the TRD skid plate.
- Compatibility with Toyota Safety Sense (2018+ models) not guaranteed.
- Sensor may be located behind the tubework based on grill model.
Victory 4x4 Tacoma Front Winch Bumper | Blitz | 3rd Gen (16+)
Our Blitz winch bumper for the 3rd Gen Tacoma is designed to integrate with your factory front bumper fascia for a clean look with maximum recovery options. This made in the USA bumper features an integrated 20" lightbar mount, 3/4" recovery tabs, plus provisions for many industry standard winches. Available tubework option includes a bull bar for extra front end protection. A fairlead block off plate is included for those that don't yet have, or need, a winch. The bumper is coated in a 2 stage satin textured black powdercoat over durable zinc primer finish. It requires very minimal cutting so you can easily go back to stock if needed. Only requires cutting the lower valance piece which is covered by stock trim.Listed weights are with no tubing; single hoops and prerunner tube work add roughly 10 lbs in steel, 5lbs in aluminum; full grill and light protection tubing adds 30 lbs in steel, 15lbs in aluminum. (Not all tubing options are available on all bumpers.)
Looking for answers to common questions about us or our products? See our FAQ here.
41 Questions asked on Tacoma Front Winch Bumper | Blitz | 3rd Gen (16-23)
•
Ask us anything
Q
Michael Aaron McHugh • 04/05/2020, 11:30:05 PM
will the collision/cruise sensor still work if the bumper has the bull bar tubework?
A
04/06/2020, 2:43:39 PM
We do not recommend any tubework on our bumpers with the front radar system.
Q
Chris • 04/19/2020, 8:05:04 PM
Is the blitz bumper available in aluminium for the 3rd gen Tacoma ?
Will a warn VR10s fit in this bumper on a 3rd gen tacoma without removing the solenoid pack ?
A
04/20/2020, 3:13:59 PM
The 3rd gen Taco Blitz is not yet available in aluminum but it's on our short list. You will need to relocate the solenoid box on the 3rd gens.
Q
Blake Brewer • 05/11/2020, 10:56:42 PM
Can I use a Hi-Lift jack on this bumper?
A
05/15/2020, 1:52:09 PM
Yes
Q
Ben Collier • 06/06/2020, 9:53:22 AM
Three questions:
1. Brian, did you defect from JCR Off-Road to Victory 4x4 or are they related companies>\? I suspect the latter.
2. Are you planning for the aluminum Gen 3 Tacoma version of the Blitz to be winch capable?
3. I may have missed it in the Gen 3 Tacoma Blitz install video, did you determine the weight of the OEM hardware removed in order to provide a basis to calculate the net weight of the installed Blitz (with tube work). I ask to help set up the preload offset adjustment on the new front coil/struts to accommodate the Blitz / Warn VR 10-S winch combo.
BTW, your videos are terrific!
Cheers,
Ben Collier
A
06/10/2020, 4:43:34 PM
1) Victory 4x4 and JCR are sister companies, Brian is still with both :) 2) This is on the list in aluminum, but we don't have an ETA. 3) Sorry we didn't weigh the factory parts, but even with the steel bumper you shouldn't have to adjust pre-load based on the bumper alone.
Q
Stephen Gerhold • 09/06/2020, 10:41:03 AM
What is the best thing to use for touch up on the powdercoat? I have a couple of small rock chips on my front bumper.....
A
09/09/2020, 3:00:07 PM
Rustoleum textured black works great.
Q
Nate Tourangeau • 09/29/2020, 1:59:54 PM
Will the smittybuilt x20 comp 10,000 pound winch fit in the bumper
A
10/01/2020, 1:40:01 PM
Yes
Q
James Parker Cunneen • 10/13/2020, 4:34:19 PM
Where can I use a hi-lift hack on this bumper?
A
10/16/2020, 3:25:50 PM
Yes, no problems.
Q
Tom • 12/24/2020, 10:18:26 AM
For my 3rd Gen Tacoma: Am I able to install the Blitz Bumper as well as a front hitch receiver (Ex: CURT Front Mount Trailer Hitches Front Mount Trailer Hitches - 31075)?
A
12/30/2020, 4:56:07 PM
No, they will not work together. You may be able to bolt a "Step Bumper Receiver" on the bottom of the bumper though. You'd just have to drill and work around the winch if installed.
Q
Jason Brown • 12/24/2020, 5:25:42 PM
Hi is there enough room to mount a license plate? I'm required to have a front plate in my state of idaho.
A
12/30/2020, 4:56:07 PM
We offer a FAIRLEAD LICENSE PLATE FLIP for this UNI-FPF-PC (https://www.victory4x4.com/product/UNI-FPF-PC.html)
Q
JOSEPH • 01/08/2021, 10:47:57 AM
WHAT SIZE D RING SHACKLES GO WITH THIS BUMPER? THANKS.
A
01/08/2021, 3:32:27 PM
3/4"
Q
Dean • 01/28/2021, 11:46:29 PM
Can you send me the size of the lightbar opening. Do you guys have a diagram with dimensions?
A
02/02/2021, 12:30:16 PM
The cutout is 21 x 1.5
Q
Shaun • 01/29/2021, 10:37:39 AM
Is the aluminum bumper any lighter than the steal? Also will this bumper fit the Warn VR EVO 10-S WINCH or the Warn ZEON 10-S WINCH? Please elaborate if solenoid packs need to be relocated.
A
02/02/2021, 12:30:16 PM
The aluminum bumper is half the weight. Without modifying the truck, both winches will need remote solenoid packs. If you modify one grill support bracket slightly by cutting it or bending it out of the way either winch can be squeezed in with integrated solenoids.
Q
Andres Galeana • 02/16/2021, 1:20:42 AM
Will this work with a Rough Country 12000LB pro series electric winch?
A
03/01/2021, 3:13:17 PM
Yes, but you may need to relocate the solenoid box.
Q
Jefferson • 02/25/2021, 11:19:06 PM
Are the d ring mounts in the aluminum version still rated for recovery?
A
03/01/2021, 3:13:17 PM
Yes
Q
Michael • 03/05/2021, 10:57:30 AM
Will this bumper work with the warn 9.0RC winch and the factor 55 short drum competition fair lead? Also, will the tube work interfere with an SR trim level Toyota safety sense?
A
03/05/2021, 1:10:49 PM
It will work with the Factor 55. The Warn 9.0RC will fit, you may or may not have to relocate the solenoid.
Yes, the tube work could interfere with the TSS. We would recommend going with no tube work for TSS.
Q
Andre • 04/06/2021, 2:49:36 AM
1. Are you able to sell the bumper without the logo in the center of the lightbar cutout? 2. Do you plan on making a stage 2 high clearance add on the same way the Slimeline Hybrid Front Bumper does?
A
04/12/2021, 1:13:17 PM
1. No we don't, sorry. 2. No plans for that.
Q
Collin • 05/16/2021, 10:13:57 PM
Is it possible to install a wench after installing the bumper or will I have to take the whole thing off to get the wench in if I were to install the bumper first?
A
05/21/2021, 9:59:41 AM
You would need to pull the bumper to install a winch.
Q
Tommy • 05/30/2021, 11:32:37 AM
I purchased this bumper for my taco and a Warn Evo 10-s winch, do I need some type of relocation kit to make it work?
A
06/04/2021, 10:30:55 AM
You would either need to relocate the sednoid box, or bend/cut the factory bumper/grille support bracket directly above the winch. On our shop Tacoma we bent about .75" of this bracket over and the winch fit fine.
Q
Christopher Fields • 08/01/2021, 11:32:04 AM
aluminum ,, is it available yet.
A
08/12/2021, 4:01:01 PM
Yes, you can select it from the drop down list when you order.
Q
Ryan • 09/13/2021, 6:46:28 PM
Do you know by how much/if this changes the approach angle of an OEM truck? Also, I know you don't recommend any tubework for trucks with the front radar system in the grill, but, hypothetically, if someone were to get one with a tube, do you suspect it would actually interfere with the sensor that is inches above and away from the bar?
A
09/23/2021, 1:26:44 PM
It changes the approach angle very little. With the pro grille we haven't gotten any errors with the tube on the shop truck, but that doesn't mean it's safe in all situations.
Q
James • 10/11/2021, 11:17:25 PM
Is it a good idea to mount a hiift Jack to the tube work while off-road with Hilift tube mount?
A
10/18/2021, 12:42:50 PM
That would work fine.
Q
Arthur • 11/02/2021, 6:53:11 PM
For the Blitz Bumper, if you don’t want to add a winch, do you still have to relocate the cooler? Also could you what the hole diameter is on the recovery tabs on the front of the bumper? Thanks so much!
A
11/05/2021, 10:29:40 AM
It won't be necessary without a winch and may or may not be with a winch depending on the winch model. The hole diameter on the recovery tabs is 1".
Q
Melissa • 11/02/2021, 10:23:11 PM
Will the 18" Diode Dynamics light bar fit without needing much modification?
A
11/05/2021, 10:25:31 AM
The mounts measure about 22" apart. The lightbar will be narrower than the light opening and the hardware will likely be too narrow to reach the mounts.
Q
Sean • 12/21/2021, 8:01:35 PM
Will the blitz winch bumper fit on a 2021 tacoma trd offroad
A
12/22/2021, 1:13:34 PM
Yes, it will.
Q
Sean • 12/22/2021, 7:37:44 PM
Will a Warn VR EVO 10-S WINCH - 103253 fit the blitz tacoma bumper
A
12/28/2021, 11:09:35 AM
Yes, you have to slightly bend or trim a grille support bracket above that winch. Then you won't have to relocate the winch control box.
Q
burke • 03/10/2022, 1:46:05 AM
Do the Steel and Aluminum versions look any different (angles, smoothness) ? Can you tell in the photos which is which?
A
03/10/2022, 12:43:08 PM
It is difficult to tell the difference from the outside. You are able to tell from the backside of the bumper as the steel will be 3/16" vs. 1/4" on the aluminum.
Q
Ryan • 03/30/2022, 3:44:22 PM
Do you think the lead time of 60-90 days for this bumper will change any time soon? This is my preferred choice, but I'd prefer having a setup before the end of summer. Thanks!
A
04/04/2022, 8:24:55 AM
Contact the customer service guys for up to date lead times! 269-459-8447
Q
Matt • 04/03/2022, 9:04:03 PM
Will the Smittybilt X2O GEN3 10K Winch fit in the bumper without relocating the control box or any other modification?
A
04/06/2022, 1:17:26 PM
We haven't tried that winch specifically. Many winches require the solenoids to be relocated, our assumption is that one will also.
Q
Ryan • 04/06/2022, 12:53:38 PM
Does the lead time change for steel vs aluminum?
A
04/06/2022, 1:20:55 PM
Sometimes slightly. Assume a week or so.
Q
Matt • 05/22/2022, 12:56:12 PM
My state requires a front plate. Can I mount a front plate on this bumper?
A
05/23/2022, 10:19:53 AM
You can using our fairlead license plate flip up bracket!
Q
Ryan • 07/25/2022, 4:30:51 PM
Do you know if the moster winch 9500 lbs by Ironman 4x4 will fit? https://ironman4x4america.com/monster-winch-9500lbs-12v-electric-synthetic-rope/
A
08/15/2022, 4:47:54 PM
It will fit fine.
Q
Sean Martinez • 08/29/2022, 12:28:44 PM
What’s the total weight on the aluminum bumper for the 3rd gen Tacoma with no bar
A
08/30/2022, 10:33:52 AM
About 35lbs
Q
cody aulbach • 10/25/2022, 10:22:16 PM
Will the xpower 10,000lb non intergraded winch fit inside bumper without any problems?
A
10/27/2022, 10:07:38 AM
As long as the side mounted solenoid box can be remote mounted, it should fit based on dimensions.
Q
Nick Chinn • 12/20/2022, 11:49:59 PM
Is the (Harbor Freight) Badlands Apex 12K lbs winch from harbor freight compatible? I know the pack can be relocated but that is the winch im planning on using.
A
01/03/2023, 2:29:09 PM
Yes, it's compatible.
Q
kc combs • 02/07/2023, 10:46:34 AM
What is the total weight of the steel bumper
A
02/14/2023, 4:18:03 PM
63 (lbs)
Q
Jason T. • 04/16/2023, 6:36:11 PM
When installed, would this bumper in steel and the way it's mounted be sufficiently strong enough to push a disabled vehicle at low speeds?
A
04/17/2023, 7:59:35 PM
That is not something we have tried. This bumper doesn't alter the factory crush points in the frame, so that is a concern for using it to push anything.
Q
Andrew • 05/09/2023, 7:04:42 PM
What winch brand & model fit this Blitz front bumper the best, with the least amount of modification?
A
05/22/2023, 5:12:36 PM
Our winch plates are pretty universal in that sense. If you are looking for an option, the Warn Evo 10-S is a great winch.
Q
Connor • 07/14/2023, 6:55:12 PM
If I'm not planning on adding a winch, can I install this bumper without cutting the OE bumper?
A
11/21/2023, 2:47:44 PM
You'll still need to cut the factory bumper to install ours.
Q
Jim • 03/23/2024, 1:38:49 AM
Do you know if the mounting brackets for the Diode Dynamics Stealth light bar would fit over your bumper mount brackets?
The light bar bracket mounts on the 2 outside bolts and extends over the bracket towards the front of the truck to mount to the LED bar in the bottom of the front grille lowest position.
It's a 30" light bar so it will not fit on the bumper.
I have the light bar and want to keep it, but I really like your bumper too!
here is a link to it. https://www.diodedynamics.com/2016-2023-toyota-tacoma-stealth-light-bar-kit.html
Thank you!
A
06/05/2024, 4:57:22 PM
The mounting brackets for likely interfere with the bumper mounts, however it is not something that we have physically verified.
Q
Kevin Danesi • 03/25/2024, 0:40:46 AM
I see that the question has been brought up before, but as for the collision sensors on the Pro Grille - I understand its not recommended to have the tube work (but lets be serious, the tubework makes this thing 1000% better) - I am curious if the tubework causes any extra lights to illuminate on my dash... Did your test vehicle sensors even notice the tubework?
A
07/17/2024, 11:58:19 AM
Our truck did not have any dash lights come on. However, we are not able to test how the sensor reads the tube work in all situations. There is potential that the sensor could pick up on the tube work while driving which could cause an unsafe situation.
Q
Danny Cook • 04/19/2024, 1:27:16 AM
Can the grill still be easily removed with the bar installed on the bumper?? Looks tight in the pictures.
A
06/07/2024, 12:13:16 PM
Yes, the grill can still be removed with the bumper installed.
Currently Viewing Reviews with a rating of 4. Click here to reset.
0
0
0
3
20
Dan Watson (Indy) | January 27th, 2023
Bought the unfinished bumper. The workmanship was 5 stars, no doubt. Welds, cutouts, everything about it was excellent. Watching their install vid I was missing three bolts that connect the oil cooler relocation/where you attach cowl to bottom of bumper. Also I had two bolts/nuts I have know idea what they went to. Not a big deal as I have a back up rig to drive. If not this might have been a one star review as my wife was out of town, I live in the country, and we don't know a lot of people here.
Note From Victory 4x4: Dan, we sincerely apologize for any missing hardware! If we can help any more with this installation, please reach out to our customer service team.
Roy | December 2nd, 2021
I bought this based on a friend’s recommendation. Overall it looks beefy, good quality steel and welds.
My issues:
1. Missing several bolts so I had to source locally
2. Bottom mounts were damaged in shipping since it was not packaged well in those areas
3. The powder coating seems thin. I have several scuffs/bare spots just from installation and I was VERY delicate throughout. I am wary of long term how it will hold up.
Overall, not sure if I would re-buy again. Looks good, good customer support, priced well. However as stated above, I am a little leery of long term durability of the powder coating.
Josh (FL) | November 28th, 2021
The bumper fits great and looks great. The only issue I have is my kit did not come with the relocation brackets so the winch I planned to install is still sitting in my garage. Hopefully they can send them out asap so I can reinstall with the winch.
Please note: Install videos are meant to be used as a guide, and aren't always the most up to date information on product installation and improvements.
Please be sure to read the PDF installation instructions as well.
Please be sure to read the PDF installation instructions as well.
Related Products
#overlanding Tee
$25.00
Fairlead License Plate Flip
$149.00
GX Rear Bumper | Strike | 550 (24+)
$1,949.00